Throughout the project, we’ll post questions and comments that have been submitted on comment cards collected at community meetings, sent via email or submitted via the website.

779 results found
Comments per page 10 | 25 | 50 | 100 View All Export to CSV
← Previous 10 Next 10 →

Showing 21-30 comments of 779

Zoning Change

We are currently zoned R1 and with the latest map, it changes us to RN2. So what does that mean exactly and what are the differences from the R1 we currently are zoned.Thank you!
Staff Reply:
The proposed RN-2 zone is a single family residential district very equivalent to the existing R-1. The major difference is the proposed minimum lot size in RN-1 of 5,000 square feet, designed to accommodate lots in some of Knoxville's older neighborhoods. Please see the Residential District Comparison Table for additional information. https://recodeknoxville.com/wp-content/uploads/2018/10/Knoxville-Residential-Districts-Comparison.pdf

Hillside Ridgetop Protection Zone

I see from the map that my property and that of my two neighbors is almost entirely covered with the Hillside Ridgetop Protection Zone. What does that mean for us? Can we still cut and plant new trees? The property of one of my neighbors is entirely level. Why would it be included in the HP zone?
Staff Reply:
The proposed Hillside Protection standards would limit the density (# of dwelling units) and the land disturbance permitted in new developments. The limitation would be on new developments on property with a slope of more than 15%. The limitations would not apply to existing single family homes and existing lots of record, nor would they restrict the cutting or planting of trees. The notation of HP on the zoning map is an indication that the property appears to be in the hillside area and that review of the property's slope is warranted.

Spence Place

I own the property at Spence place in the Island home neighborhood.It is a through lot bounded by Spence place on the south and the Tennessee river on the north.My lot is 132 ft wide, 429 ft deep. The house is set back 40 ft from the road, the attached carport is set back 26 ft from the road. The east side set back is 5 ft for the carport and 50 ft on the west side.It seems to me It should be classified as RN-1 not RN-2.It seems to me that all of the parcels on the north side of Spence should have been designated RN-2 since they meet the size and set back requirements of RN-1.
Staff Reply:
The properties north of Spence Pl were included as RN-2 to have one consistent zone for the Island Home neighborhood. Due to your concerns, I have added a map comment based on your email so it can be reviewed for the next map draft. You may also add an additional map comment here. These comments take 24 hours to show up so you may not see it right away.

Scope Of Project

Please advise whether this project will review for purposes of potential modification, the process for changing existing zoning and the use on review process. Will the roles the MPC and the Chief Building Official of the City of Knoxville, as well as the definition in the Code of Ordinances be subject to review/discussion.
Staff Reply:
The process for changing the existing zoning of a property, which requires MPC review and recommendation followed by City Council approval, is established by state statute and will not change. The use on review process, the roles of MPC and the Chief Building Official, and definitions in the zoning ordinance likely will be reviewed and discussed.

Recode Map

Is there a way to download the draft version of the new zoning map?
Staff Reply:
The new map, along with tools to compare the existing zoning and provide comments, are available for online viewing.

Mixed Use Development In C-h Highway Commercial Zoning District

Hi,I have a question related to the C-H Highway Commercial Zones. As currently drafted, would a mixed-use development with residential multifamily above a commercial ground floor be permitted in a C-H zone? I see in the Use Matrix that "Dwelling - Above the Ground Floor" is permitted in a C-H zone, but I don't understand whether that implies, multifamily, single family, etc.Thanks for the help!
Staff Reply:
The intent is to permit either a single dwelling or multiple dwellings on the upper floor(s) of a building in the C-H zone. We will clarify this so there is no confusion.

Hillside Protection

I notice that a portion of my property, that includes about half of my house, falls within an area designated HP. I can't find any definitive resource regarding HP online, except references back to 2008-2011. I'm interested in what restrictions the HP designation will place, both on me as an established homeowner and on the newly developed apartment complex abutting my property. Can you point to a resource so we may understand what's about to happen to us?
Staff Reply:
The hillside protection standards would place density and land disturbance limitations on new development located on properties within the HP overlay (properties with grades in excess of 15%). The greater the grade of the property, the greater the limitations on density and land disturbance. The hillside protection standards would not apply to existing single family homes and existing lots of record, so your home would be exempt. As a developed project, the apartment complex abutting your property would not be subject to any limitations either. If the apartment complex proposed expansion (new buildings), the hillside protection standards might limit density (# of dwelling units) and land disturbance.

Hillside Protection?

I own property on Sherrod Rd and it has the small green dots with Hillside and Ridge Protection.  What does that mean to the property owner?
Staff Reply:
The Hillside Overlay (HP) section of the code can be found on page 8-12 here.These regulations apply to all lots within the HP Overlay District with the exception of existing single-family homes (which yours appears to be) and existing lots of record for a single-family dwelling existing as of the effective date of this Code.If you have any further questions please let us know.

Auto Sales And Service Facility

I just built a auto sales and service facility on my property. The recode doesn’t appear to be for auto retail. Please review this and call me.
Staff Reply:
The designation proposed for your property on the draft map is IG (General Industrial). Given the use of your property, CH (Highway Commercial) would be a better designation. I will make this note on the draft map and the change will be made on the next draft map, which will be available in mid to late April.Thanks for contacting us regarding this.

C-g-2 Code / Multi-tenant Housing Numbers

I have a question regarding multi-tenant housing numbers. According to the code C-G-2, how many people can reside in an apartment of the same family-last name? If not the same family-last name?Thank you.
Staff Reply:
Thanks for your interest in the Knoxville zoning code update. In response to your comment:I have a question regarding multi-tenant housing numbers. According to the code C-G-2, how many people can reside in an apartment of the same family-last name? If not the same family-last name?Zoning ordinances can address the development density (number of dwelling units per acre, etc) but generally do not address the number of persons, related or unrelated, who can reside in a dwelling unit. The proposed update of the City of Knoxville zoning ordinance does not establish a density (number of dwelling units per acre) cap in the C-G-2 zone. Density in this proposed district would be addressed by building height, lot size, need for parking etc. The building code does establish standards for minimum square footage per occupant.

779 results found
Comments per page 10 | 25 | 50 | 100 View All Export to CSV